拆胎机（扒胎机）压胎慢可能由多种原因造成，以下是一些可能的原因及其解决方法：
内部压力不足：拆胎机内部的气压或液压不足，导致压胎时无法提供足够的压力，从而减慢压胎速度。
胎垫与轮胎接触不紧密：胎垫与轮胎之间如果存在间隙或接触不紧密，会导致压胎时产生过多的空气，进而影响压胎速度。
轮胎胎面与胎垫之间有异物：轮胎胎面与胎垫之间如果存在硬物或异物，会导致接触面积不均匀，从而影响压胎速度。
内胎不完全排气：在拆装轮胎时，如果内胎未完全排气，会影响压胎时的空气压力，进而影响压胎速度。
气动开关或气压问题（针对气动扒胎机）：气动扒胎机的气压不正常或气动开关出现异常，也可能导致转速慢的情况。
缺少润滑油：拆胎机如果缺少必要的润滑油，可能会导致运转部件之间的摩擦增大，从而降低压胎速度。
调整胎垫位置：检查胎垫与轮胎的接触情况，如存在间隙或接触不紧密，应重新调整胎垫的位置，确保其与轮胎紧密接触。
清理异物：在压胎前，仔细检查轮胎胎面与胎垫之间是否存在异物，如有需要清理干净。
完全排气：在拆装轮胎时，应先将内胎的气门开关拧松，等到排气结束之后再进行上胎，并且在上胎时调节好内胎的气压。
检查气动开关和气压：对于气动扒胎机，应定期检查气压是否正常以及气动开关是否异常，如有需要应及时维修或更换。
添加润滑油：定期检查拆胎机的运转部件是否缺少润滑油，如缺少应及时添加，以确保运转部件之间的摩擦处于正常范围内。
综上所述，拆胎机压胎慢的原因可能涉及多个方面，需要逐一排查并采取相应的解决方法。在操作过程中，应严格按照使用说明书和安全操作规程进行，以确保操作的安全性和有效性。
Tire removal machine (tire removal machine) slow tire pressure may be caused by a variety of reasons, the following are some possible causes and solutions:
Reason analysis internal pressure is insufficient:
The pressure or hydraulic pressure inside the tire removal machine is insufficient, resulting in the failure to provide enough pressure when the tire is pressed, thereby slowing down the tire speed.
Pad and tire contact is not close: If there is a gap between the pad and the tire or the contact is not close, it will cause excessive air to be produced when the tire is pressed, which will affect the tire speed.
There is a foreign body between the tire tread and the tire pad: If there is a hard object or foreign body between the tire tread and the tire pad, it will cause the contact area to be uneven, thus affecting the tire press speed.
Incomplete exhaust of the inner tube: When removing and assembling the tire, if the inner tube is not completely exhaust, it will affect the air pressure during tire press, and then affect the tire press speed. Pneumatic switch or air pressure problem (for pneumatic tire picker) : The air pressure of the pneumatic tire picker is abnormal or the pneumatic switch is abnormal, which may also lead to slow speed. Lack of lubricating oil: If the tire removal machine lacks the necessary lubricating oil, it may lead to increased friction between the moving parts, thereby reducing the tire press speed.
Solution: Check and increase the internal pressure: regularly check the internal pressure or hydraulic pressure of the tire removal machine to ensure that it is within the normal range.
If insufficient, the pressure should be increased in time. Adjust the position of the tire pad: check the contact between the tire pad and the tire. If there is a gap or the contact is not close, the position of the tire pad should be readjust to ensure that it is in close contact with the tire.
Clean up foreign matter: Before pressing the tire, carefully check whether there is foreign matter between the tire tread and the tire pad, and clean it up if necessary.
Complete exhaust: When removing and assembling the tire, the valve switch of the inner tube should be loosened first, and then the tire will be loaded after the exhaust is finished, and the pressure of the inner tube will be adjusted when the tire is loaded.
Check the pneumatic switch and air pressure: for the pneumatic tire scraper, it is necessary to regularly check whether the air pressure is normal and whether the pneumatic switch is abnormal, and if necessary, it should be repaired or replaced in time.
Add lubricating oil: Regularly check whether the moving parts of the tire removal machine lack lubricating oil, if lacking, it should be added in time to ensure that the friction between the moving parts is within the normal range. In summary, the reasons for the slow tire press of the tire removal machine may involve many aspects, and it is necessary to investigate one by one and take appropriate solutions. In the process of operation, it should be strictly in accordance with the instruction manual and safety operation procedures to ensure the safety and effectiveness of the operation.
Oct-19-2024
admin
