The Roadbuck R600 wheel aligner uses 3D measurement software to automatically measure and diagnose chassis data reports, which are included
1: Inspect the vehicle before positioning before adjusting the chassis data, which helps to find potential problems with the vehicle
The record of the vehicle’s chassis and tires inspection items before the vehicle is quadruple aligned, including shock absorbers, wheel bearings, brakes, steering tie rods, tie rod ball joints, tie rod rubber sleeves, pads, knuckle arms, steering axles, swing arms, swing arm bushings, ball joints at component connections, bushings at component connections, elastic elements, universal joints, whether there is loosening, repair and replacement
Tire inspection items include: tire pressure value maintained at 2.5, dynamic balance, wear (uniform wear, outer edge wear, center wear, inner edge wear, wavy wear, block wear, bulge or crack,
2: According to the car factory nameplate factory age tire model and chassis code to select the model, enter keywords or model model, you can quickly select the model data, there are five units of measurement can be selected: 100 points, 60 points, millimeters 100 points, 60 points, Inch
3: Voice broadcast, the software sets up voice broadcast, and the system will automatically voice remind you to enter the next process at the end of each link
4: 3D dynamic measurement link, trolley measurement function: Panasonic hand brake, gear in neutral N gear, according to the voice reminder to use the backward cart and then forward cart to complete the cart measurement mode, cart 20.0–20.5 between, one time to measure most of the required data, data more accurate
The advantage of cart measurement is that the compensation hub is not round or the master operation fixture does not clamp the hub, and the measurement accuracy is more accurate
5: The link of kingpin measurement: first pull up the handbrake and fix the foot brake, loosen the corner disc fixing pin, click the Start start icon, measure the kingpin, first turn the steering wheel to the left to 10.0–10.5, the stop icon appears, stabilize the steering wheel and wait for the arrow to jump, and then turn the steering wheel to the right until the stop icon appears between 10.0 and 10.5, stabilize the steering wheel and wait for the arrow jump interface to complete the kingpin measurement and enter the vehicle four-wheel alignment detection result interface
6: Data preview function: This interface is the vehicle four-wheel alignment detection results {front wheel kingpin tilt, camber, toe, rear wheel camber, toe-in)
7: Secondary data, vehicle size detection data results display: can detect the front wheel track, rear wheel track, left wheelbase, right wheelbase, cross wheel track, thrust angle, axle offset, retraction angle and other data of the vehicle chassis, to help customers understand the problem of body angle, including whether the girder is deformed, so that you can judge whether you have bought a second-hand accident car, the real situation of the chassis
8: Value-added data: This interface displays the corresponding data: steering front expansion angle, steering angle, thrust angle, and retraction angle (this interface is an optional function, and some models do not have this function)
9: Rolling radius measurement: provide accurate tire diameter measurement, this interface displays the radius of the four-wheel tire, if the numerical deviation is too large, detect the tire pressure and tire wear degree, such as some models with air suspension, you can judge the degree of tire pattern wear through the data, and the reason for the uneven air suspension,
10: This interface is the body height measurement interface, take out the left and right side targets of the front wheel and place them directly above the tires, and the edge of the metal body (this interface is an optional function)
Secondary data: Toe-in camber leaning backward of the left front wheel, camber inclusive angle Toe-in of the right front wheel camber camber, inward camber inclusive angle
The total toe-in propulsion angle of the front wheel, the toe-in camber of the left rear wheel, and the toe-in camber of the right rear wheel
11: Chassis data analysis report: diagnostic results and recommendations
12: Road Racer four-wheel adjustment interface, at this time, the steering wheel should be fixed with a steering wheel retainer, and then the shunting should be carried out
The shunting sequence is successively wheeled and then front, so the rear wheel data is displayed first
Practical link: display the rear wheel data, start to adjust the rear wheel data,
The front wheel data is displayed, and the front wheel data is adjusted
Displays the data of the camber of the four wheels and starts to adjust the camber of the four wheels
Jacking up body adjustment function: it is convenient for the operator to lift the vehicle, and the wheels are suspended using the Roadbuck camber adjustment auxiliary tool developed by Roadbuck itself to adjust the four-wheel alignment angle
Displays the data for the four wheels toe, and begins to adjust the total toe of the four wheels
This link also has a jacking body adjustment function to facilitate the operator to adjust the inclination, which can avoid repeated adjustments and improve efficiency and accuracy.
This interface is the steering wheel level check function, this function after the four-wheel alignment is adjusted, turn the steering wheel left and right in the same place many times, and then return to the right to observe whether the value in the middle is within plus or minus 0.1, otherwise re-shunting
13: This interface of Roadbuck is to set up the automatic tracking lifting function, click to save and click to exit after setting, this interface is to control the lifting speed of the lifting column beam, which can be fast or slow, and is suitable for shunting use
14: Add customer information to print data reports, deliver customer maintenance projects in the form of text or graphics, and retain customer information for a return visit to the user after half a year, and the license plate number is required to be saved
15: Loocke clicks on System Management, clicks on Report Management, and performs operations such as report query and deletion
16: Click on the vehicle management to enter the interface, you can add, modify and delete the model data, and pay attention to the conversion of units when adding and modifying the model data
This screen is the Add and Remove Car Models interface
On the left, select the regional brand of the model you want to add
Enter the added model and data
Select the system user, enter the password, and confirm to add the model
17: Click on the system settings, enter the password, set the kingpin mode: ordinary only kingpin measurement, special kingpin measurement and maximum steering angle measurement,
Set data display: This is the unit in which the value displayed by the positioning software is set
Click on the camera settings to adjust the exposure and intensity of the camera light board, which should be carried out under the guidance of the technical engineer, and cannot be set by yourself
Click on the COM setting, which is also under the guidance of a technical engineer
Language selection function
Click Help to go to the 3D animation demonstration
Guangdong Roadbuck Electromechanical Equipment Co., Ltd. specializes in the production of high-end wheel maintenance equipment such as wheel aligners, tire removal machines, balancing machines, etc., and is an automobile maintenance equipment manufacturer integrating R&D, production, sales and service. “Roadbuck” is committed to the R&D, production and sales of high-end automobile maintenance equipment, continuously innovating around the needs of customers, launching professional automobile maintenance service solutions, and striving to improve the user experience and create a good reputation with high-quality products and considerate services. At present, Rodrople’s products have been sold to more than 60 regions abroad, serving more users in the auto maintenance industry. Brand Website https://www.roadbuck3d.com/
Mar-04-2025
admin
